IFM Electronic efectro 500 Скачать руководство пользователя

Страница: 11 / 17

•

Change from menu level 1 to menu level 2:

►

Press [Mode/Enter] until [EF] is

displayed�

If the submenu is protected with an

access code, [Cod1] flashes in the

display�

►

Press [Set] and keep it pressed until

the valid code no� is displayed�

►

Press [Mode/Enter] briefly�

When delivered by ifm electronic: no

access restriction�

►

Press [Set] briefly�

> The first parameter of the submenu is

displayed (here: [Uni])�

With the user interface of the program ifm Container:

►

Activate the [EF] button�

If menu level 2 is protected by an access code, the input field for the code no� is

activated�

►

Enter the valid code no�

•

Locking / unlocking

The unit can be locked electronically to prevent unintentional settings�

►

Make sure that the unit is in the

normal operating mode�

►

Press [Mode/Enter] + [Set] for 10 s�

> [Loc] is displayed�

During operation: [LOC] is briefly displayed if you try to change parameter values�
For unlocking:

►

Press [Mode/Enter] + [Set] for 10 s�

> [uLoc] is displayed�

Factory setting: unlocked�

Содержание efectro 500


















Результаты поиска

Содержание efectro 500

Отзывы:

Похожие инструкции для efectro 500

Бренды по названию

Популярные бренды

IFM Electronic efectro 500, Руководство по эксплуатации

Результаты поиска

Содержание efectro 500

Отзывы:

Похожие инструкции для efectro 500

Бренды по названию

Популярные бренды