Ier 520 Скачать руководство пользователя | Manualshive

Страница: 25 / 41

background image

d) Removing the Roll of Media Backing

The roll of media backing needs to be removed each time you load
new media into the printer.

To remove the media backing (1) from the printer, proceed as
follows:

a)

Remove retaining pin (2).

b) Slide the roll of media backing (1) out of the printer.

c)

Replace the retaining pin on the rewind spindle.

25

2

1

n06902a3.chp

Tue Sep 22 15:02:27 1998

Profil couleur : DØsactivØ(e)

Composite Ecran par dØfaut

«
...
23
24
25
26
27
...
»

Содержание 520










































Отзывы:

Нет отзывов

Похожие инструкции для 520

Бренд: EBS Страницы: 4

Бренд: NCR Страницы: 38

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 858

WorkCentre 4265

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 11

Бренд: Oce Страницы: 340

Бренд: Muratec Страницы: 112

Бренд: Ricoh Страницы: 406

Бренд: IriSys Страницы: 21

Бренд: Oce Страницы: 230

WorkCentre 6655i

Бренд: Xerox Страницы: 282

Бренд: Sagem Страницы: 154

Бренд: Ricoh Страницы: 284

Бренд: Lexmark Страницы: 2

Бренд: Dell Страницы: 4

Бренд: Dell Страницы: 68

Ink-Free Printer PZ310

Бренд: Dell Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды