IEM eConnect Скачать руководство пользователя | Manualshive

Страница: 8 / 26

background image

For your safety

36

Portable and mobile high frequency transmitters, such
as mobile phones, may affect data transmission.

Transmission of data via mobile communication
networks may be disrupted by other devices, even if
those devices comply with the applicable transmission
requirements specified by CISPR.

3.6

Operation

WARNING!

Danger as a result of humidity!

▪

Only use the

eConnect

in dry locations and

avoid direct contact with water. The

eConnect

is not watertight.

WARNING!

Risk of data loss if power supply is disconnected!

▪

The

eConnect

should remain constantly

connected to the power supply.

WARNING!

Danger caused by delayed data transmission

▪

Successful data transmission is dependent on
external providers. A delayed transmission
can therefore never be ruled out. Do

not

use

eConnect with life preserving or life
supporting medical products, as delayed data
transmission might directly endanger the
patient.

WARNING!

Risk of data loss if data connection is lost!

▪

The relevant source measuring device should
always be relatively close to the

eConnect

to

avoid data transmission errors.

▪

Please also note that the ranges of the
measuring devices might differ.

«
...
6
7
8
9
10
...
»

Содержание eConnect



























Отзывы:

Нет отзывов

Похожие инструкции для eConnect

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: Tar River Страницы: 61

Бренд: H&S Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды