IEI Technology KINO-KX Series Скачать руководство пользователя страница 52

Страница: 52 / 110

KINO-KX SBC

Page 40

4.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the KINO-KX

may result in permanent damage to the KINO-KX and severe injury to

the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the KINO-KX. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the KINO-KX, or any other electrical component is handled, the

following anti-static precautions are strictly adhered to.



Wear an anti-static wristband

: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.



Self-grounding

: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.



Use an anti-static pad

: When configuring the KINO-KX, place it on an

anti-static pad. This reduces the possibility of ESD damaging the KINO-KX.



Only handle the edges of the PCB

: When handling the PCB, hold the PCB

by the edges.

4.2 Installation Considerations

NOTE:

The following installation notices and installation considerations should

be read and understood before installation. All installation notices must

be strictly adhered to. Failing to adhere to these precautions may lead

to severe damage and injury to the person performing the installation.

Содержание KINO-KX Series















































































































Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды

IEI Technology KINO-KX Series, Руководство пользователя

Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды