IEI Technology KINO-KX Series Скачать руководство пользователя страница 92

Страница: 92 / 110

KINO-KX SBC

Page 80



Administrator Password

Use the

Administrator Password

to set or change a administrator password.



User Password

Use the

User Password

to set or change a user password.

5.6 Boot

Use the

Boot

menu (

BIOS Menu 26

) to configure system boot options.

Main

Advanced

Chipset

Security

Boot

Save & Exit

Boot Configuration

Bootup NumLock State

[On]

Quiet Boot

[Enabled]

Launch PXE OpROM

[Disabled]

Option ROM Messages

[Force BIOS]

UEFI Boot

[Disabled]

Boot Option Priorities

Driver Option Priorities

Select the keyboard
NumLock state

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 26: Boot



Bootup NumLock State [On]

Use the

Bootup NumLock State

BIOS option to specify if the number lock setting must

be modified during boot up.



EFAULT

Allows the Number Lock on the keyboard to be

enabled automatically when the computer system

boots up. This allows the immediate use of the

10-key numeric keypad located on the right side of

the keyboard. To confirm this, the Number Lock LED

light on the keyboard is lit.

Содержание KINO-KX Series















































































































Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды

IEI Technology KINO-KX Series, Руководство пользователя

Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды