IEI Technology KINO-KX Series Скачать руководство пользователя страница 70

Страница: 70 / 110

KINO-KX SBC

Page 58

5.3.3 RTC Wake Settings

The

RTC Wake Settings

menu (

BIOS Menu 5

) configures RTC wake event.

Advanced

RTC Wake Settings

Wake system with Fixed Time

[Disabled]

Enable or disable System
wake on alarm event. When
enabled, System will
wake on the
date::hr::min::sec
specified

----------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 5: RTC Wake Settings



Wake system with Fixed Time [Disabled]

Use the

Wake system with Fixed Time

option to enable or disable the system wake on

alarm event.



Disabled

EFAULT

The real time clock (RTC) cannot generate a wake

event



Enabled

If selected, the

Wake up every day

option appears

allowing you to enable to disable the system to wake

every day at the specified time. Besides, the

following options appear with values that can be

selected:

Wake up date

Wake up hour

Wake up minute

Wake up second

After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

Содержание KINO-KX Series















































































































Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды

IEI Technology KINO-KX Series, Руководство пользователя

Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды