IEI Technology KINO-KX Series Скачать руководство пользователя страница 93

Страница: 93 / 110

KINO-KX SBC

Page 81



Off

Does not enable the keyboard Number Lock

automatically. To use the 10-keys on the keyboard,

press the Number Lock key located on the upper

left-hand corner of the 10-key pad. The Number

Lock LED on the keyboard lights up when the

Number Lock is engaged.



Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.



Disabled

Normal POST messages displayed



Enabled

EFAULT

OEM Logo displayed instead of POST messages



Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.



Disabled

EFAULT

Ignore all PXE Option ROMs



Enabled

Load PXE Option ROMs.



Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.



Force

BIOS

EFAULT

Sets display mode to force BIOS.



Keep

Current

Sets display mode to current.



UEFI Boot [Disabled]

Use the

UEFI Boot

option to enable or disable to boot from the UEFI devices.



Enabled

Boot from UEFI devices is enabled.

Содержание KINO-KX Series















































































































Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды

IEI Technology KINO-KX Series, Руководство пользователя

Результаты поиска

Содержание KINO-KX Series

Отзывы:

Похожие инструкции для KINO-KX Series

Бренды по названию

Популярные бренды