IEI Technology eKINO-BT страница 125 Скачать руководство пользователя

Страница: 125 / 157

eKINO-BT Mini-ITX SBC

Page 111

5.6 Boot

Use the

Boot menu

(

BIOS Menu 21

) to configure system boot options.

Main

Advanced

Chipset

Security

Boot

Save & Exit

Boot Configuration

Bootup NumLock State

[On]

Quiet Boot

[Enabled]

UEFI Boot

[Disabled]

Launch PXE OpROM

[Disabled]

Option ROM Messages

[Force BIOS]

Boot Option Priorities

Select the keyboard
NumLock state

---------------------

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 21: Boot

Bootup NumLock State [On]

Use the

Bootup NumLock State

BIOS option to specify if the number lock setting must

be modified during boot up.

On D

EFAULT

Allows the Number Lock on the keyboard to be

enabled automatically when the computer system

boots up. This allows the immediate use of the

10-key numeric keypad located on the right side of

the keyboard. To confirm this, the Number Lock LED

light on the keyboard is lit.

Off

Does not enable the keyboard Number Lock

automatically. To use the 10-keys on the keyboard,

press the Number Lock key located on the upper

left-hand corner of the 10-key pad. The Number

Lock LED on the keyboard lights up when the

Number Lock is engaged.

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды