IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 96 / 157

eKINO-BT Mini-ITX SBC

Page 82

5.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to

certain system settings. This chapter outlines the options that can be changed.

NOTE:

Some of the BIOS options may vary throughout the life cycle of the

product and are subject to change without prior notice.

5.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be

activated in one of two ways.

1. Press

the

DEL

key as soon as the system is turned on or

2. Press

the

DEL

key when the “

Press DEL or F2 to enter SETUP

”

message appears on the screen.

If the message disappears before the

DEL or F2

key is pressed, restart the computer and

try again.

5.1.2 Using Setup

Use the arrow keys to highlight items, press

NTER

to select, use the PageUp and

PageDown keys to change entries, press

for help and press

to quit. Navigation

keys are shown in the following table.

Key

Function

Up arrow

Move to previous item

Down arrow

Move to next item

Left arrow

Move to the item on the left hand side

Right arrow

Move to the item on the right hand side

Increase the numeric value or make changes

Decrease the numeric value or make changes

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды