IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 102 / 157

eKINO-BT Mini-ITX SBC

Page 88

5.3.2.1.1 Serial Port 1 Configuration

Serial Port [Enabled]

Use the

Serial Port

option to enable or disable the serial port.

Disabled

Disable the serial port

Enabled D

EFAULT

Enable the serial port

Change Settings [Auto]

Use the

Change Settings

option to change the serial port IO port address and interrupt

address.

Auto D

EFAULT

The serial port IO port address and interrupt address

are automatically detected.

IO=3F8h;

IRQ=4

Serial Port I/O port address is 3F8h and the interrupt

address is IRQ4

IO=3F8h;

IRQ=3, 4

Serial Port I/O port address is 3F8h and the interrupt

address is IRQ3, 4

IO=2F8h;

IRQ=3, 4

Serial Port I/O port address is 2F8h and the interrupt

address is IRQ3, 4

IO=3E8h;

IRQ=3, 4

Serial Port I/O port address is 3E8h and the interrupt

address is IRQ3, 4

IO=2E8h;

IRQ=3, 4

Serial Port I/O port address is 2E8h and the interrupt

address is IRQ3, 4

5.3.2.1.2 Serial Port 2 Configuration

Serial Port [Enabled]

Use the

Serial Port

option to enable or disable the serial port.

Disabled

Disable the serial port

Enabled D

EFAULT

Enable the serial port

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды