IEI Technology eKINO-BT Скачать руководство пользователя страница 126

Страница: 126 / 157

eKINO-BT Mini-ITX SBC

Page 112

Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.

Disabled

Normal POST messages displayed

Enabled D

EFAULT

OEM Logo displayed instead of POST messages

UEFI Boot [Disabled]

Use the

UEFI Boot

BIOS option to allow the system to boot from the UEFI devices.

Disabled D

EFAULT

Disables to boot from the UEFI devices.

Enabled

Enables to boot from the UEFI devices.

Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.

Disabled D

EFAULT

Ignore all PXE Option ROMs

Enabled

Load PXE Option ROMs.

Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.

Force

BIOS

EFAULT

Sets display mode to force BIOS.

Keep

Current

Sets display mode to current.

5.7 Save & Exit

Use the

Save & Exit

menu (

BIOS Menu 22

) to load default BIOS values, optimal failsafe

values and to save configuration changes.

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Бренды по названию

Популярные бренды