background image

Explanation of each part

 

 

Link LED

 

This indicator shows Link status of Transmitter (TX) and Receiver (RX).

 

LED blink: searching

 

LED light lit: linked

 

 

Video LED

 

This indicator shows video status.

 

LED off: no video signal / abnormal status

 

LED blink: searching

 

LED lit: linked

 

 

Digital LED display

 

This digital LED shows current setup status.

 

H: under activation

 

U: under software upgrade 

 

1: setup to 5180MHz

 

2: setup to 5240MHz

 

3: setup to 5765MHz

 

4: setup to 5805MHz

 

 

CH Button

 

Press for 1sec.: This is to change CH as below.

 

1→2→3→4→1→…→

 

   

 

  Press and hold for 3sec.: 

 

This is only required for service maintenance purpose, 

 

and paring mode (pair up SSID and Password for each TX and RX).

 

 

Mode Button

 

Press and hold for 3sec.: This will change the MODE as below.

 

   

 

 

Normal Mode

HDMI Video Transmission Mode

 

*Link LED & Video LED turn to RED

 

 

RTSP Mode

Streaming Mode

 

*Link LED & Video LED turn to Yellow

 

**Video  signal  of  HDMI  output  from  RX  is  automatically  regulated  to  720P 
output only during RTSP Mode

 

 

 

The device reboots automatically when Mode change is made.

 

11 

Содержание CW-1dx





































Отзывы: