background image

Form Number TM61096 

Rev 2 Nov 2010 

Physical and Environmental Characteristics 

Characteristics 

Description 

Dimensions (W×H×L) 

84mm×188mm×41mm 

Weight (with battery) 

230g 

Environmental characteristics 

Description 

Temperature operating 

0 to +50°C 

Non-Operating 

-20 to +60°C 

Humidity (operating) 

<80% R.H. 

Altitude Operating 

2,000M (6560 ft.) 

Non-Operating 

12,300M (40354 ft.) 

Vibration & shock Operating 

MIL-T-28800E TYPE II Class 5 
2.66gRMS, 5 to 500 Hz, 3axes 
(10 minutes each) 

Indoor Use 

Indoor Use 

Certifications and compliances 

Safety 

IEC 61010 and designed to meet UL 3111 specifications 

Input rating 

V / Ω: Category 

III

 1000 Volts 

Over voltage category 

CAT 

III

: Distribution level mains, fixed installation. 

CAT 

II

: Local level mains, appliances, portable equipment 

CAT 

I

: Signal level, special equipment or parts of equipment, 

telecommunication, electronics. 

Pollution Degree 2 

Do not operate in environments where conductive 
Pollutants may be present. 

EC Declaration 
of Conformity 

Meets the intent of Directive 89/336/EEC for Electromagnetic 
Compatibility and Low Voltage Directive 73/23/EEC for specifica -
tions as listed in the official Journal of the European Communites: 
En 55011 Class A: Radiated and Conducted 

Emissions. 

En 50082-1 Immunity: IEC 801-2 Electrostatic Discharge 

IEC 801-3 RF Radiated 

En 61010-1 Safety requirements for electrical equipment for 

measurement, control, and laboratory use. 

Содержание SPLIT-JAW 61-096
















Отзывы: