background image

EVOMAX - MULTILINE FLUE KITS

6

FLUE DESIGN

!

3.0 FLUE DESIGN

3.01  The following standards are relevant to the  

 

 

construction, installation & testing of flue systems.

 

BSEN 14471 

Plastic Chimneys –  

 

 

   

 

requirements and test methods

 

BSEN 1856-1 

Metal Chimneys – Requirements

 

BSEN 1859 

Metal Chimneys – Test methods

 

BS 6644   

Installation & Maintenance    

 

   

 

of gas fired hot water  

 

 

   

 

boilers 70kW – 1.8MW

3.0.2  The Flue Stack must be specified by a Flue Specialist
3.0.3  Design of the connecting flue spigot must refer to the 

 

 

dimensions of the mating collar (Fig 3.1).

3.0.4  The Polypropylene header and EPDM seal are certified  

 

to BSEN 14471. 

3.0.5  Integrity of the flue joints and safety of operation must  

 

be proven by the installer.

3.0.6  The flue resistance at ‘A’ in Figure 3.2 is not permitted to  

 

exceed the maximum static pressure specification [Pmax]  

 

quoted in Table 3.3 when operating at the maximum 

 

 

capacity.

IMPORTANT:  LEAKAGE OF FLUE PRODUCTS INTO THE ROOM WILL DEPLETE  

THE OXYGEN LEVEL & INHIBIT SAFE COMBUSTION.

3.0.7  The flue route should be planned to enable the least  

 

directional change, one elbow is recommended as  

 

depicted in Figure 3.2.

3.0.8  The flue pipe diameter must be at least 200mm, larger  

 

diameters will permit longer flue length.

3.0.9  The flue material must be suitable for condensing  

 

operation.

3.0.10  The terminal guard must prevent the ingress of objects  

 

greater than 15mm diameter to comply with EN15502. 

3.0.11  The Flue Terminal design should be selected to create the  

 

least resistance and not compromise the potential flue  

 

length. A wire mesh type is recommended with a 

 

 

14mm grid.

3.0.12  Rain ingress may be ignored as the header design  

 

enables excess water to be discharged through the  

 

condensate drain.

FIGURE 3.1 

(CASCADE HEADER INTERFACE DETAIL - FEMALE FLUE SOCKET CONNECTION)

 

 

70.0 mm

                    Sealing Ring

PR-RING 1-LIPS HR-EPDM 200 ZWART

In

side

 20

2.

mm

+0

.6 

mm

-1

.0

 mm

Cascade Header Interface Detail

Cascade Header

NOTE: Connecting flue must comply with CE approval requirements

Содержание Evomax 30

















Отзывы: