background image

WARNING

If the information in these instructions is not followed exactly, a fire or explosion may result, 

causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of 

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

 

Do not try to light any appliance.

 

Do not touch any electrical switch; do not use any phone in your building.

 

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s 

instructions.

 

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service 

agency or the gas supplier.

H

NSF/ANSI 372

Keep this manual near this boiler for future reference 

whenever maintenance or service is required.

*  The wetted surface of this product contacted by consumable water 

contains less than one quarter of one percent (0.25%) of lead by 
weight.

User’s Information Manual

NCB-H Condensing Combi-Boilers

Model

NCB-190/060H

NCB-190/080H

NCB-240/110H

NCB-240/130H

NCB-250/150H

Summary of Contents for NCB-190/060H
































Reviews: