Ideal Boilers LOGIC COMBI C24 Скачать руководство пользователя страница 35

Страница: 35 / 72

Installation and Servicing

SECTION 2 - INSTALLATION

WARNING.

Whilst effecting the required gas tightness test and purging air from the gas installation,

open all windows and doors, extinguish naked lights and

DO NOT SMOKE.

As part of the commissioning process, the combustion of this appliance must be checked

and the Benchmark Checklist completed. A flow chart to assist is provided on page 73.

A. Electrical Installation
1.

Checks to ensure electrical safety should be carried out by

a competent person.

ALWAYS carry out the preliminary electrical system

checks, i.e. earth continuity, polarity, resistance to earth

and short circuit, using a suitable test meter.

B. Gas Installation
1.

The whole of the gas installation, including the meter,

should be inspected and tested for tightness and purged in

accordance with the recommendations of BS.6891.

In IE refer to IS.813.

Purge air from the gas installation by the approved methods

only.

2.22 COMMISSIONING AND TESTING

GENERAL

Please Note

: The combustion for this appliance has

been checked, adjusted and preset at the factory for

operation on the gas type defined on the appliance

data plate.

DO NOT

adjust the air/gas ratio valve.

Having checked:
- That the boiler has been installed in accordance

with these instructions.

- The integrity of the flue system and the flue seals,

as described in the Flue Installation section.

Proceed to put the boiler into operation as follows:

CHECK THE OPERATIONAL (WORKING) GAS

INLET PRESSURE

Set up the boiler to operate at maximum rate by

opening hot tap to maximum flow.

With the boiler operating in the maximum rate

condition check that the operational (working) gas

pressure at the inlet gas pressure test point complies

with the requirements - refer to “Gas Supply” on page

12.
Ensure that this inlet pressure can be obtained with all

other gas appliances in the property working.

Gas Pressure

Test Point

Gas

Supply

ATTENTION !

IT IS A CONDITION OF THE MANUFACTURER’S WARRANTY THAT THE

BENCHMARK COMMISSIONING CHECKLIST IS FULLY COMPLETED

AND LEFT WITH THE APPLIANCE

INST

ALLA

TION

Содержание LOGIC COMBI C24









































































Результаты поиска

Содержание LOGIC COMBI C24

Отзывы:

Похожие инструкции для LOGIC COMBI C24

Бренды по названию

Популярные бренды

Ideal Boilers LOGIC COMBI C24, Установка и обслуживание

Результаты поиска

Содержание LOGIC COMBI C24

Отзывы:

Похожие инструкции для LOGIC COMBI C24

Бренды по названию

Популярные бренды