background image

13

Installation and Servicing

 

SECTION 1 - GENERAL

1.10 TERMINAL

The terminal assembly can be adapted to accommodate various 

wall thicknesses. Refer to Section 2.9.

1.11  AIR SUPPLY

It is NOT necessary to have a purpose-provided air vent in the 

room or internal space in which the boiler is installed. Neither 

is it necessary to ventilate a cupboard or compartment in which 

the boiler is installed, due to the low surface temperatures of 

the boiler casing during operation; therefore the requirements of       

BS.6798, Clause 12, and BS. 5440:2 may be disregarded.

1.12 WATER CIRCULATION SYSTEM

IMPORTANT.

 

A minimum length of 1 metre of copper pipe MUST be fitted 

to both flow and return connections from the boiler before 

connection to any plastic piping.
The central heating system should be in accordance with BS.6798 

and, in addition, for smallbore and microbore systems, BS.5449.

WATER TREATMENT - 

Refer to Section 1.19.

1.13 BOILER CONTROL INTERLOCKS

Central heating system controls should be installed to ensure that 

the boiler has no demand when there is no requirement from the   

system, in compliance with Building Regulations.
Heating systems utilising full thermostatic radiator valve control 

of temperature in individual rooms should also be fitted with a 

room thermostat controlling the temperature in a space served by 

radiators not fitted with such a valve.

When thermostatic radiator valves are used, the space heating 

temperature control over a living / dining area or hallway having 

a heating requirement of at least 10% of the minimum boiler heat 

output should be achieved using a room thermostat, whilst other 

rooms are individually controlled by thermostatic radiator valves.  

However, if the system employs thermostatic radiator valves on all 

radiators, or two port valves, then a bypass circuit must be fitted 

with an automatic bypass valve to ensure a flow of water should 

all valves be in the closed position.

1.14 ELECTRICAL SUPPLY

WARNING.

 

This appliance must be earthed. 

Wiring external to the appliance MUST be in accordance with 

the current I.E.E. (BS.7671) Wiring Regulations and any local 

regulations which apply. For IE reference should be made to the 

current ETCI rules for electrical installations.
The mains supply to the boiler and system wiring centre shall 

be through one common fused double pole isolator and for new 

heating systems, and where practical replacement installations, 

the isolator shall be situated adjacent to the appliance.

1.15 CONDENSATE DRAIN 

(Refer to Section 2.15

)

A condensate drain is provided on the boiler. This drain must be 

connected to a drainage point on site. All pipework and fittings in 

the condensate drainage system MUST be made of plastic - 

no 

other materials may be used.

IMPORTANT.

Any external runs must be in accordance with BS.6798.

The drain outlet on the boiler is sized for standard 21.5mm 

overflow pipe.  It is a universal fitting to allow use of different 

brands of pipework.

Содержание LOGIC COMBI C24









































































Отзывы: