Ideal Boilers LOGIC COMBI C24 Скачать руководство пользователя

Страница: 20 / 72

Installation and Servicing

SECTION 2 - INSTALLATION

The wall mounting template is located on the internal protective

packaging. The template shows the position of the fixing and rear

flue centre holes for a standard installation

Care MUST be taken to ensure the correct holes are drilled.

Tape template into the required position, ensuring its squareness

by hanging a plumbline as shown.

If fitting a side flue, extend the flue centreline onto the side by

155mm

on a standard wall fix or

200mm

if using a stand-off

bracket.

Mark the following on to the wall:

The selected group of wall mounting screw holes.

The centre position of the flue duct. Marking both the centre

and the circumference of the flue duct.

Remove the template plate from the wall.

2.5 WALL MOUNTING TEMPLATE

2.6 PREPARING THE WALL

IMPORTANT.

Ensure that, during the cutting operation, masonry falling

outside of the building does not cause damage or personal

injury.

Cut the flue hole (preferably with a 5” core boring tool),

ensuring that the hole is square to the wall.

Both wall faces immediately around the cut hole should be

flat.

Drill 2 mounting holes (marked from template) with a 7.5mm

/ 8mm masonry drill and insert the plastic plugs, provided,

for the wall mounting plate.

Locate 2 No.14 x 50mm screws in the wall mounting plate

(one at each side, in any of the 3 holes provided at each

side) and screw home. Ensure mounting bracket is level.

2.8 MOUNTING THE BOILER

1. Ensure the plastic plugs are removed from both the CH

and DHW connections before mounting the boiler.

Note. Boiler may contain residual water.

2. Lift the boiler onto the wall mounting plate (refer to the

Introduction section for safe handling advice), locating it

over the two tabs.

2.7 FITTING THE WALL MOUNTING PLATE

Screw the wall mounting plate to the wall using 2 wall plugs

(previously fitted) with the 2 screws provided.

Choose one of the 2 sets of slots in left and right bank.

Ensure that at least one of the screws is fitted into a top slot

and the mounting bracket is level.

A** - See Diagram in

Section 1.16

Extended centre line

155

(200)

3G9495

Section

through wall

Note.

Check all of the hole

positions before drilling.

Side flue only

5" diameter hole

Rear flue only

5" diameter hole

esp9496

Example of fixing

INST

ALLA

TION

Содержание LOGIC COMBI C24









































































Результаты поиска

Содержание LOGIC COMBI C24

Отзывы:

Похожие инструкции для LOGIC COMBI C24

Бренды по названию

Популярные бренды

Ideal Boilers LOGIC COMBI C24, Установка и обслуживание

Результаты поиска

Содержание LOGIC COMBI C24

Отзывы:

Похожие инструкции для LOGIC COMBI C24

Бренды по названию

Популярные бренды