background image

3

PART 1

INSTALLATION

SAFETY CONSIDERATIONS

INSTALLATION OF OIL FIRED HEATING UNITS
SHALL BE IN ACCORDANCE WITH THE
REGULATION OF AUTHORITIES HAVING
JURISDICTION AND THE CAN/CSA B139 OR
USA/NFPA NO.31-1992 INSTALLATION CODE FOR
OIL BURNING EQUIPMENT.

DO NOT OPERATE FURNACE IN A CORROSIVE
ATMOSPHERE CONTAINING CHLORINE, FLUORINE
OR ANY OTHER DAMAGING CHEMICALS.

DO NOT STORE OR USE GASOLINE, OR OTHER
FLAMMABLE VAPOURS AND LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.

1)

SAFETY LABELLING AND SIGNAL
WORDS

1.1)

Danger, Warning and Caution:

The signal words 

DANGER, WARNING

 and 

CAUTION

are used to identify levels of hazard seriousness.  The
signal word 

DANGER

 is only used in product labels to

signify an immediate hazard.  The signal words

WARNING

 and 

CAUTION

 will be used on product

labels and throughout this manual and other manuals
that may apply to the product.

1.2)

Signal Words:

DANGER 

– Immediate hazards which 

WILL

 result in

death or serious injury.

WARNING

 – Hazards or unsafe practices which

COULD

 result in death or injury.

CAUTION

 – Hazards or unsafe practices which 

COULD

result in personal injury or product or property damage.

1.3)

Signal Words in Manuals

The signal word 

WARNING

 is used throughout this

manual in the following manner:

WARNING

WARNING

The signal word CAUTION is used throughout this
manual in the following manner:

CAUTION

2)

SAFE INSTALLATION
REQUIREMENTS

WARNING

WARNING

Installation or repairs made by unqualified
persons can result in hazards to you and
others.  Installation MUST conform with
codes or, in the absence of local codes,
with codes of the country having
jurisdiction.

The information contained in this manual
is intended for use by a qualified service
technician familiar with safety procedures
and equipped with the proper tools and
test instruments.

Failure to carefully read and follow all
instructions in this manual can result in
furnace malfunction, property damage,
personal injury and/or death.

NOTE:

 It is the personal responsibility and obligation of

the customer to contact a qualified installer to ensure
that the installation is adequate and conforms to
governing codes and ordinances.

WARNING

WARNING

Fire hazard

The furnace must be installed in a level
position, never where it will slope to the
front.

If the furnace were installed in that
position, oil could drain into the furnace
vestibule and create a fire hazard, instead
of draining properly into the combustion
chamber

.

!

!

!

Содержание OLR Series










































Отзывы: