icontrols PULSE Скачать руководство пользователя страница 4

Страница: 4 / 30

lectrical

SUPPLY VOLTAGE:

110-130 or 208-240V Vac, 1ph Input (All incoming power to be

connected in provided junction box)

BATTERIES:

½ HP= 2 x 5Ah, ¾ HP= 2 x 7Ah, 1 HP= 2 x 9Ah, 2 HP= 3 x 9Ah

CONTROL VOLTAGE:

24Vdc, 1A Power/Connections supplied for activation and

reversing devices

AUX RELAY:

1 SPDT Programmable Relay (factory default to activate on Open

Limits)

Safety

PHOTO-EYE or THRU-BEAM Polarized Photo-eye Sensor/Reflector with Bracket or Thru-Beam

SENSOR:

sensor provided with unit as non-impact reversing device protection.

POWER OUTAGE

Battery Backup to open/close the door in case of power-outage.

OPERATION:

3/8” ratchet socket for manual crank open/close as added

redundancy.

Maximum Recommended Counter balance Sectional Door size

Pulse 500:

up to 200 Square Feet

Pulse 750:

up to 350 Square Feet

Pulse 1000:

up to 500 Square Feet

Pulse 2000:

over 500 Square Feet

IMPORTANT

WARNING – These instructions are intended for experienced personnel trained for service and

installation of sectional doors and operators. All safety precautions and local codes must be

followed.

READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

Have qualified service personnel make necessary repairs to ensure door is operating

smoothly without any unusual noise. Install operator only on a smoothly operating and well

balanced door.

Remove all pull ropes and remove locks (unless mechanically and/or electrically

interlocked to the power unit) connected to the door before installing the operator.

A commercial/industrial door operator that has exposed moving parts capable of causing

injury to persons or employs a motor deemed indirectly accessible by clause 10.6 by virtue

of its location above the floor shall include:

a. Install the door operator at least 2.44m (8 ft) or more above the floor: or

b. If the operator must be installed less than 2.44m (8ft) above the floor, then exposed

moving parts must be protected by covers or guarding; or

c. Both a. and b.

Do not connect the operator to the supply power until instructed to do so.

Locate the control station: (a) within sight of the door, and (b) at a minimum height of 1.53m

(5 ft) above floors, landings, steps, or any other adjacent walking surface and (c) away from

all moving parts.

Install an Entrapment Warning Placard next to the control station in a prominent location.

Содержание PULSE































Результаты поиска

Содержание PULSE

Отзывы:

Бренды по названию

Популярные бренды

icontrols PULSE, Руководство по установке и инструкции пользователя

Результаты поиска

Содержание PULSE

Отзывы:

Бренды по названию

Популярные бренды