8
SET MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
8-12
MENU
» SET > Connectors >
USB AF/IF Output
Output Select
(Default: AF)
Selects the signal output from [USB].
•AF: An AF signal is output.
•IF: A 12 kHz IF signal is output.
AF Output Level
(Default: 50%)
Sets the AF output level of [USB], when “Output
Select” of USB is set to “AF.”
AF SQL
(Default: OFF (Open))
Selects whether or not to output the audio from [USB],
according to the squelch state, when “Output Select”
of USB is set to “AF.”
•OFF (Open): The squelch is always opened
regardless of the transceiver’s squelch
level.
•ON:
The squelch opens and closes,
according to the transceiver’s squelch
level.
AF Beep/Speech��� Output
(Default: OFF)
Sets the Beep and Speech audio output setting of
[USB], when “Output Select” of USB is set to “AF.”
•OFF: The beep and speech audio are not output.
•ON: The beep and speech audio are output.
IF Output Level
(Default: 50%)
Sets the IF output level of [USB], when “Output
Select” of USB is set to “IF.”
MENU
» SET > Connectors >
LAN AF/IF Output
Output Select
(Default: AF)
Selects the signal output from [LAN].
•AF: An AF signal is output.
•IF: A 12 kHz IF signal is output.
AF SQL
(Default: ON)
Selects whether or not to output the audio from [LAN],
according to the squelch state, when “Output Select”
of LAN is set to “AF.”
•OFF (Open): The squelch is always opened
regardless of the transceiver’s squelch
level.
•ON:
The squelch opens and closes,
according to the transceiver’s squelch
level.
MENU
» SET > Connectors >
MOD Input
ACC MOD Level
(Default: 50%)
USB MOD Level
(Default: 50%)
LAN MOD Level
(Default: 50%)
Sets the modulation input level of each interface.
DATA OFF MOD
(Default: MIC,ACC)
DATA MOD
(Default: ACC)
In the SSB, AM, or FM mode, selects the connector(s)
to input the modulation signal when the data mode is
OFF, or ON.
MENU
» SET > Connectors >
ACC SEND Output
144M
(Default: ON)
430M
(Default: ON)
1200M
(Default: ON)
Selects whether or not to switch the SEND terminal
output level of [ACC] to the Low level during
transmitting.
•OFF: Does not switch to the Low level.
•ON: Switches to the Low level.
MENU
» SET > Connectors >
USB SEND/Keying
TIP:
This is the setting for the terminal used for data
communication when you operate the transceiver
from the software on the PC.
When you connect the transceiver to a PC with a
USB cable, 2 COM ports are recognized on the PC.
To confirm USB (A)/USB (B), open the COM port
properties, and confirm the “Value” of the “Details” tab.
USB SEND
(Default: OFF)
Sets the USB terminal of the transceiver to receive the
SEND signal from the software on the PC.
Select the same terminal as the terminal set by the
software.
L
You cannot select the terminal which is already selected in
the “USB Keying (CW)” or “USB Keying (RTTY)” item.
USB Keying (CW)
(Default: OFF)
Sets the USB terminal of the transceiver to receive the
CW Keying signal from the software on the PC.
Select the same terminal as the terminal set by the
software.
L
You cannot select the terminal which is already selected in
the “USB SEND” or “USB Keying (RTTY)” item.
USB Keying (RTTY)
(Default: OFF)
Sets the USB terminal of the transceiver to receive the
RTTY Keying signal from the software on the PC.
Select the same terminal as the terminal set by the
software.
L
You cannot select the terminal which is already selected in
the “USB SEND” or “USB Keying (CW)” item.
