167
14
SET MODE
%EYPAD
54.
$EFAULT/&&
Turn the external keypad ON or OFF for keyer mem-
ory transmission.
See page 26 for the equivalent circuit of an external
keypad and connection.
s/&&
4HEEXTERNALKEYPADDOESNOTFUNC
-
tion.
s+%9%23%.$)NTHE#7MODEPUSHINGONEOFEX
-
ternal keypad switches transmits the
desired keyer memory contents.
53"!UDIO31,
55.
$EFAULT/&&/0%.
Select whether or not to output the audio from the
[USB] connector on the rear panel, according to the
squelch state.
The same audio signals are sent from the [USB] con-
nector and the [ACC] sockets.
- The beep tones and the voice synthesizer announce-
ments are not sent.
- The received audio output level cannot be adjusted
with the [AF] control.
s/&&/0%. 4HERECEIVEDAUDIOISALWAYSSENT
regardless of the squelch state.
s/.
4HERECEIVEDAUDIOISSENTWHENTHE
squelch is open.
53"-/$,EVEL
56.
$EFAULT
Set the input modulation level of the [USB] connector
TOBETWEENANDINSTEPS
BPS-ODE
57.
$EFAULT/&&
Turn the [DATA2] socket’s 9600 bps data transmission
ON or OFF.
s/&&&ORONLYTHEREGULARAUDIOORSLOWDATA TRANS
-
mission.
s/. &ORBPSDATATRANSMISSION
DATA OFF MOD
58.
$EFAULT-)#!##
Select the desired connector(s) for data modulation
input in the data OFF mode.
s-)#
5SETHESIGNALSFROM;-)#=
s!##
5SETHESIGNALSFROM;!##=PIN
s-)#!## 5SETHESIGNALSFROM;-)#=AND;!##=
(pin 11).
s53"
5SETHESIGNALSFROM;53"=
DATA MOD
59.
$EFAULT!##
Select the desired connector(s) for data modulation
input in the data mode.
s-)#
5SETHESIGNALSFROM;-)#=
s!##
5SETHESIGNALSFROM;!##=PIN
s-)#!## 5SETHESIGNALSFROM;-)#=AND;!##=
(pin 11).
s53"
5SETHESIGNALSFROM;53"=
#)6"AUD2ATE
60.
$EFAULT!UTO
Set the CI-V data transfer rate between 300, 1200,
4800, 9600, 19200 bps and “Auto.”
When “Auto” is selected, the baud rate is automatically
set according to the data rate of the connected con-
troller.
CI-V Address
61.
$EFAULT#H
To distinguish equipment, each CI-V transceiver has
its own Icom standard address in hexadecimal code.
The IC-9100’s address is 7Ch.
When 2 or more IC-9100’s are connected to an op-
tional CT-17
CI
-
V
level converter, rotate [MAIN DIAL] to
SELECTADIFFERENTADDRESSFOREACH)#THERANGE
is 01h to DFh.
#)64RANSCEIVE
62.
$EFAULT/.
Turn the transceive function using the CI-V system ON
or OFF.
When this item is set to ON, changing the frequency,
operating mode, etc. on the IC-9100 automatically
changes those settings on other Icom transceivers or
receivers, and vice versa.
s/&&4RANSCEIVEFUNCTION/&&
s/. 4RANSCEIVEFUNCTION/.
53"$!4!&UNC
63.
$EFAULT;='03
Two COM port numbers are assigned to the [USB]
connector. One of them is “USB1,” used for cloning
and CI-V operation. The other one is “USB2,” and the
function is selected by this item.
s
-----
: “USB2” is not used.
s2449 5SEDTOSEND2449DECODEDSIGNALS
s$6DAT 5SEDFORLOWSPEEDDATAINPUTANDOUTPUT
s)FYOUSETTHEFUNCTIONOFTHE;$!4!=JACKTO
“GPS,” and “DATA1
USB2” is selected as
the “GPS Out” item’s option, as described
below, “USB2” will be used for the low-speed
data input and GPS data output.
N
Set mode description (Continued)
