![background image](http://html2.mh-extra.com/html/icom/ic-7610/ic-7610_basic-manual_4141367059.webp)
8
SET MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
8-7
MENU
» SET >
Network
DHCP
(Default: ON( . . . ))
Turns the DHCP function ON or OFF.
IP Address
(Default: 192.168. 0. 10)
Sets the static IP address.
Subnet Mask
(Default: 255.255.255. 0 (24 bit))
Sets the subnet mask to connect to your PC or LAN
(Local Area Network), through the Ethernet.
Default Gateway
(Default:
—
)
lf you are operating the IC-7610 using the optional
RS-BA1, a default gateway setting is required.
MENU
» SET > Connectors >
CI-V
CI-V Baud Rate
(Default: Auto)
Selects the CI-V data transfer rate.
L
When “Auto” is selected, the baud rate is
automatically set according to the data rate of the
connected device.
CI-V Address
(Default: 98)
Sets the CI-V address.
L
“98h” is the default address of the IC-7610.
CI-V Transceive
(Default: ON)
Turns the Transceive function ON or OFF.
CI-V USB/LAN→REMOTE Transceive Address
(Default: 00)
Sets the address used to remotely control the
transceiver or receiver using the optional RS-BA1,
through the [USB] port.
The external equipment control signal is output from
the [REMOTE] port.
CI-V Output (for ANT)
(Default: OFF)
Enables outputting the antenna controller status
(frequency and so on) from the [REMOTE] port.
L
Address “01h” is reserved.
The usable addresses are limited to 02h ~ DFh.
CI-V USB Port
(Default: Unlink from [REMOTE])
Selects the internal connection type between the
[USB] and [REMOTE] CI-V ports.
CI-V USB Baud Rate
(Default: Auto)
Selects the CI-V data transfer rate when remotely
controlling the IC-7610 through the
[USB]
CI-V port
.
L
When “Auto” is selected, the baud rate is
automatically set according to the data rate of
external device.
L
This setting is valid only when the “CI-V USB Port”
item is set to “Unlink from [REMOTE].”
CI-V USB Echo Back
(Default: OFF)
Turns the Data Echo Back function ON or OFF, when
remotely controlling the IC-7610 through the [USB]
CI-V port.
L
This setting is valid only when the “CI-V USB Port”
item is set to “Unlink from [REMOTE].”
MENU
» SET > Connectors >
External Meter
External Meter Output (MAIN)
(Default: Auto)
External Meter Output (SUB)
(Default: Auto)
Selects the parameter (Main and Sub readout) to
output to an external meter.
External Meter Level (MAIN)
(Default: 50%)
External Meter Level (SUB)
(Default: 50%)
Sets the output level to the external meter (Main and
Sub band).
MENU
» SET > Connectors
Decode Baud Rate
(Default: 9600)
Selects the data transfer rate (Baud rate) of decoded
signals.
SEND Relay Type
(Default: MOS-FET)
Selects the switching relay type for [RELAY].
Select the suitable relay type, especially when
connecting a non-Icom linear amplifier.
ACC BAND Voltage Output
(Default: TX)
Selects the operating band voltage output from
[ACC2] (pin 4).
MIC Input DC Bias
(Default: ON)
Outputs the 8 V bias voltage (approximate) from the
microphone connector (pin 1 of [MIC]).
REF IN
(Default: OFF)
Selects the transceiver’s reference frequency signal
source.
L
This setting will be valid after restarting the transceiver.
L
If the applied reference signal is off frequency, or not high
enough, the IC-7610 will not work correctly. In that case,
select “OFF,” and then restart the IC-7610.
Network
Содержание IC-7610
Страница 1: ...BASIC MANUAL i7610 HF 50 MHz TRANSCEIVER...