ICI Caldaie 83801210 страница 12 Скачать руководство пользователя

Страница: 12 / 32

Installation

HANDLING

REX F

boilers are equipped with fittings for lifting operations and, in any case, they must be carefully moved with equipment

suitable for their dimensions and weights.

ATTENTION

The Personal Protective Equipment required by current legislation must be used.

INSTALLATION ROOM

The

REX F

boiler installation room must be for exclusive use, meet the Technical Standards and Legislation in force and equipped

with adequately sized ventilation openings.
The spaces around the boiler and towards the ceiling must be suitable for:

–

installing the appliance

–

reaching the safety devices

–

maintenance

–

repairing any breakage

–

opening the door of the installed burner, considering its opening direction (towards the right or the left)

It is recommended to position the boiler, if possible, lifted from the floor to minimise dust extraction by the burner fan.

A (*)

≥ 90°

> 600 mm

NO!

(*) A ≥ P2 (see "Size and fittings*)

IMPORTANT

–

The front space (A) must be greater than the boiler length to be able to extract the turbulators or replace a fire tube in
case of breakage.

–

In the case of several boilers installed in the same room, check the accessibility to the most remote boiler to be able to
perform ordinary and extraordinary maintenance.

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

Содержание 83801210

































Результаты поиска

Содержание 83801210

Отзывы:

Похожие инструкции для 83801210

Бренды по названию

Популярные бренды

ICI Caldaie 83801210, Инструкция по установке, использованию и техническому обслуживанию

Результаты поиска

Содержание 83801210

Отзывы:

Похожие инструкции для 83801210

Бренды по названию

Популярные бренды