background image

Maintenance

25

Maintenance

Periodic maintenance is prescribed by Law and must be performed only by qualified personnel, at least once a year or more 
frequently, depending on the boiler output and on the fuel used.
The boiler maintenance and cleaning operations are essential for its safety and to keep its efficiency high, extending its service life.

IMPORTANT

Before performing any maintenance or cleaning:

 

disconnect the power supply by positioning the system main switch and that of the burner, if any, to “

OFF

 

close the fuel supply

 

use all Personal Protective Equipment required by current Standards and Legislation

 

wait for the boiler and the system to cool down.

 

BOILER

External cleaning

To perform the external cleaning of the boiler (cover) use cloths moistened with water mixed with denatured alcohol or specific 
non-abrasive detergents. Dry the surfaces thoroughly after cleaning.

 

Internal cleaning

To perform the internal cleaning:

 

disconnect from the burner anything which may hinder the door opening

 

loosen the ring nuts with handle (1), open the door (2) and extract the turbulators (3)

2

1

3

Cooke Industries - Phone: +64 9 579 2185   Email: [email protected]   Web: www.cookeindustries.co.nz

Содержание 83801210

































Отзывы: