iCharger 308DUO Скачать руководство пользователя страница 35

Страница: 35 / 42

308DUO V1.1.0

Synchronous Balance Charger/Discharger

- 35 -

⑤

Click the iron "

" on the lower right corner, then the upgrade progress bar will appear on the lower left

corner, a tone sounds for upgrade completion when the upgrade progress bar has completed.

Note: Upgrade failed in the case of not power outages, click "

" to upgrade again; if the charger

fails to start normally, press

knob

STATUS-2

and

STOP/START-2

buttons at the same time and electrify, it

will enter the mandatory upgrade mode, then repeat the above steps to upgrade again.



Firmware Upgrades via SD Card

Create a new directory in the available SD card:

X:\Junsi\Upgrade

;

Rename the firmware file to 308DUO.BIN, and copied to the new directory;

iii

Insert the SD card into the charger, and press the

Knob, STATUS-2, STOP/START-2

at the same time and electrify,

the charger will automatically upgrade the firmware, which takes about 20 seconds.

After the upgrading is complete, the charger will reboot.

Содержание 308DUO











































Результаты поиска

Содержание 308DUO

Отзывы:

Похожие инструкции для 308DUO

Бренды по названию

Популярные бренды

iCharger 308DUO, Руководство пользователя

Результаты поиска

Содержание 308DUO

Отзывы:

Похожие инструкции для 308DUO

Бренды по названию

Популярные бренды