background image

                                                                               SERVICE MANUAL                                                            

 

2.  INSTALLATION 

 

2.1.- PLACING OF THE ICE MAKER 

 

This ice maker is not designed for outdoor operation. The icemaker should not be located next to 
ovens, grills or other high heat producing equipment.  

The  FDHD  machines  are  designed  to  operate  at  room  temperature  between  10ºC  and  43ºC  . 
There may be some difficulties in ice slab removal under the minimum temperatures.  Above the 
maximum temperature, the life of the compressor is shortened and the production is substantially 
lower. 

The air cooled FDHD (undercounter) ice makers take the air through the front section, and drive 
it off through the back and also front louvers due to their new oblique condenser structure and 
placement . Do not place anything on the top of ice maker or facing the front grille. In case the 
front  grille is either total or partially obstructed,  or due to its placement  it receives hot air from 
another device, we recommend, in case it is not possible to change the location, to install a water 
cooled machine. 

The air cooled FDHD  (modular) ice makers take the air through the back section and drive it off 
through the two lateral louvers. In the case it is not possible to respect the minimum distances 
recommended (see the picture in point 3.3) for these machines we recommend to install a water 
cooled unit. 

The location must allow enough clearance for water, drain and electrical connections in the rear 
of the ice machine. It is important that the water inlet piping does not pass near sources of heat 
so as not to lose ice production. 

 

2.2.-LEVELLING OF THE ICE MAKER 

 

Use a level on top of ice machine in order to ensure the equipment is perfectly leveled. 

Screw the leveling legs onto the bottom of the ice machine as far as possible. 

Move the machine into its final position. 

Use a level on top of the ice machine. Adjust each leg as necessary to level the ice machine from 
front to back and side to side. 

ATTENTION:

 There is an optional 90mm high casters kit that can be used in substitution of the 

standard legs. These wheels are supplied with the corresponding installation instructions. 

Содержание FDHD Series









































Отзывы: