background image

                                                                               SERVICE MANUAL                                                            

 

 

INDEX

 

1.

 

INTRODUCTION

............................................................................................................................... 4

 

1.1.- Warning ........................................................................................................................................ 4

 

1.2.-Reception of the machine .............................................................................................................. 6

 

2.

 

INSTALLATION

 ................................................................................................................................ 7

 

2.1.- Placing of the ice maker ............................................................................................................... 7

 

2.2.-Levelling of the ice maker .............................................................................................................. 7

 

2.3.-Installation of modular equipments on top of bins .......................................................................... 8

 

2.4.-Minimum distance to obstacles ...................................................................................................... 8

 

2.5.- Water supply connection .............................................................................................................. 9

 

2.6.-Drain connection ............................................................................................................................ 9

 

2.6.1 

– DRAIN FORCED CONNECTION ............................................................................................ 10

 

2.5.- Electrical connection ................................................................................................................... 11

 

3.

 

PRIOR CHECKING AND START-UP

 .............................................................................................. 12

 

3.1.- Prior checking ............................................................................................................................. 12

 

3.2.- Start-Up ...................................................................................................................................... 12

 

4.

 

SEQUENCE OF OPERATION UNDERCOUNTER MODELS (NG)

 ................................................. 14

 

4.1.

 

Undercounter Control Board .................................................................................................... 14

 

4.2.- Alarms ........................................................................................................................................ 16

 

4.2.1 Safety high pressure switch .................................................................................................... 17

 

4.2.2 Long harvest .......................................................................................................................... 17

 

4.2.3 Ice production cycle timeout ................................................................................................... 17

 

4.2.4 Faulty temperature probe ....................................................................................................... 17

 

4.3 PCB push button function ............................................................................................................. 17

 

4.4 DRAIN FORCED .......................................................................................................................... 18

 

4.4.1

 

SEQUENCE OF OPERATION .......................................................................................... 18

 

4.4.2 

 

CONTROL BOARD ........................................................................................................... 20

 

5.

 

SEQUENCE OF OPERATION -MODULAR MODELS (MS)

 ............................................................ 21

 

5.1.- Initial Start-up ............................................................................................................................. 21

 

5.2.-MS Control Board ........................................................................................................................ 23

 

5.3.- Alarms ........................................................................................................................................ 24

 

5.4.- Safety pressure .......................................................................................................................... 24

 

5.5.- Long harvest ............................................................................................................................... 25

 

5.6.-Ice production cycle timeout ........................................................................................................ 25

 

Содержание FDHD Series









































Отзывы: