background image

                                                                               SERVICE MANUAL                                                            

 

14 

4.  SEQUENCE OF OPERATION UNDERCOUNTER MODELS (NG) 

 

Once you connect the machine there is a time delay of 2 minutes during which the water valve is activated 
to ensure the water tray is filled. 

Once the time is up, the compressor starts and the pump which recirculates the water from the water tray 
to the upper distributor which provides a soft and uniform flow of water over the evaporator cells, in which 
the water starts freezing. 

When the temperature probe at the end of the evaporator reaches an adjusted value Tc (-2/-4°C) , the 
fabrication continues the fixed time with the combination of dip-switches 1-4 (see table). This way we can 
ensure the filling of the evaporator is correct in different working conditions. 

Once the fabrication is over the harvest phase starts. The pump stops, the hot gas  valve open and the 
water inlet valve open only during the time fixed in the dip-switches 5-7. Water is sprayed over the back of 
the evaporator helping unstick the slab and precooling it for the next cycle. This heat recover enhances 
the machine’s energetic efficiency. 

Once the ice slab falls into the bin, the evaporator curtain opens and closes. A magnet placed on the side 
of this curtain activates the sensor and ends the harvest cycle, advancing to the fabrication cycle. 

Once the ice bin is full, the slab does not go out completely, and this prevents the curtain from closing. If 
it remains open more than 60 seconds the machine goes into full bin state. All the components shut down 
until the ice is retired, the curtain closes, and a new cycle starts. 

4.1.  UNDERCOUNTER CONTROL BOARD  

 

 

 

Содержание FDHD Series









































Отзывы: