ICE AIR ccHPWH Series Скачать руководство пользователя страница 8

Страница: 8 / 50

The HPWH refrigeration circuit shall contain scroll compressor(s) with a maximum of 15-hp per circuit, factory

charged with R-410A refrigerant, air-source evaporator(s), water-source condenser(s), EEV regulated flow, EEV

regulated vapor injection circuit, and 4-way valve to reverse the refrigeration circuit during defrost cycles.

The water-source condenser circuit shall be provided with one of two factory options:

Double wall, brazed plate heat exchanger

with airgap and leakage ports. This option to be utilized with

direct heating of potable hot water. When this feature is selected, factory mounted heat-trace will be

provided on all internal hydronic components, wired to a unit mounted 115v/1ph/60hz terminal strip

intended for field provided emergency power source.

Single wall, brazed plate heat exchanger

. This option to be utilized with indirect heating of potable hot

water. Typical applications include glycol circuits for exterior piping that transfer heat via an interior

mounted double wall heat exchanger that services the domestic hot water circuit. Heat-trace is not

provided with this option because glycol operation is assumed.

Supply and return piping shall be 316L stainless steel with flanged supply and return connections. Clean out
ports (1” NPT) shall be provided on the supply and return headers to allow for preventive maintenance of the

heat exchanger circuits. Pipes and heat exchangers to be insulated with 40mm rubber cotton insulation.

Operation guidelines for defrosting and drainage in winter

In winter, when the temperature is lower than 32°F (0

℃

), if the unit is powered off for any reason, then water

must be drained from the unit to prevent damage to the hydronic components. Draining the system of water

shall be carried out as follows:

Operational guideline

：

Isolate the inlet and outlet water connections external to the unit. Ensure the internal isolation valves on each

heat exchanger are open. Open the drain cap at the bottom of inlet water pipe to drain water. Keep the drain

port open until the next use. Open the vent valve to facilitate complete draining of water from the heat

exchangers. Using compressed air or a wet/dry vacuum to assist water removal is recommended.

Содержание ccHPWH Series



















































Результаты поиска

Содержание ccHPWH Series

Отзывы:

ICE AIR ccHPWH Series, Руководство по установке и обслуживанию, Страница: 8 / 50

Результаты поиска

Содержание ccHPWH Series

Отзывы: