ICE AIR ccHPWH Series Скачать руководство пользователя страница 21

Страница: 21 / 50

The heat pump has three modes of energy level adjustment when it is running. The principle is to calculate the

load required by the system based on the current temperature of the water tank and the set temperature, so as

to turn on the corresponding number of compressors. When the required compressor is turned on, it enters the

"energy adjustment during normal operation". At this time, as the water temperature rises, the number of

compressors to be turned on/off is adjusted according to the difference between the current temperature of the

water tank and the set temperature.

Single Unit Operation

When the unit is enabled, the calculation method of the number of compressors to be opened is as followed:

Heating: Nneed

＝（

Thset

－

）×

Cmax

／

Tmax

Nneed: number of compressors to be enabled;

T: temperature of the control object;

Cmax: number of total compressors in the system;

Tmax: [temperature difference needed of enabling all compressors, 6

℃

by default];

THSET: [heating target temperature] or [hot water target temperature].

During operation, there are 4 temperature conditions for LOADING, HOLDING, UNLOADING, URGENCY

STOP.

HSET

: Setting temperature of heating mode

ULD

: Temperature differential of unloading

: Temperature differential of loading

LOADING: When the object temperature is in this area, turn on a compressor every 60 seconds until all

compressors are turned enabled.

HOLDING: When the object temperature is in this area, unit keeps running and has no actions.

UNLOADING: When the object temperature is in this area, turn off a compressor every 60 seconds until all

compressors are turned off.

URGENCY STOP: When the object temperature is in this area, turn off a compressor per second until all

compressors are turned off.

Multiple Units Operation

Multiple unit operation follows the same rules for operation, with each water heater providing additional stages

of heating.

Содержание ccHPWH Series



















































Результаты поиска

Содержание ccHPWH Series

Отзывы:

Бренды по названию

Популярные бренды

ICE AIR ccHPWH Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание ccHPWH Series

Отзывы:

Бренды по названию

Популярные бренды