ICE AIR ccHPWH Series Скачать руководство пользователя страница 49

Страница: 49 / 50

•

Power on for 8 hours before starting.

Parts replacement

Replacing parts should use the parts provided by the manufacturer, do not replace with 3rd party

parts.

Refrigerating system

The system is factory charged with refrigerant. If the refrigerant charge is found to be low, evacuate the

charge and check for leaks.

If repair welding is needed, the system must be drained of gas before welding

Connect the vacuum tube to the low-pressure side refrigerant injection nozzle

Vacuum the system line with vacuum pump, vacuum for more than 3 hours, confirm that the multi-

meter indicating pressure in the specified range

Replenish the refrigerant.

fter reaching the desired vacuum limit and holding it for 3-hours or more, the system can be

charged with refrigerant. The appropriate refrigerant filling amount has been indicated on the

nameplate and in the main technical parameters table.

The charging amount of refrigerant will be affected by the ambient temperature. If the required

charging amount is not reached and cannot be recharged, the water can be circulated and the unit

can be started for charging. If necessary, the low-voltage control switch can be temporarily short-

circuited

Slowly fill the system with refrigerant and check the suction and exhaust pressure.

Warning: Do not inject oxygen, acetylene or other flammable or toxic gases into the refrigeration

system during leak detection and air tightness test. Only high-pressure nitrogen or

refrigerant can be used

Disassemble compressor

If the compressor needs to be removed, please follow the following steps

：

•

Turn off the unit power supply.

•

Remove the compressor power connector.

•

Remove compressor suction and exhaust pipe.

•

Disconnect the compressor retaining bolt.

•

Move the compressor.

Auxiliary electric heater

Air-source heat pump capacity will derate when the ambient temperature drops. Be sure to reference the

performance data when selecting equipment. For areas that experience temperatures below 5°F for

extended times, the outlet temperature may drop below 140°F. Secondary electric heaters can be used to

either boost temperature or supplement the load to counteract the derate in performance caused by low

Содержание ccHPWH Series



















































Результаты поиска

Содержание ccHPWH Series

Отзывы:

Похожие инструкции для ccHPWH Series

Бренды по названию

Популярные бренды

ICE AIR ccHPWH Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание ccHPWH Series

Отзывы:

Похожие инструкции для ccHPWH Series

Бренды по названию

Популярные бренды