ICE AIR ccHPWH Series Скачать руководство пользователя страница 29

Страница: 29 / 50

Note:

In the branch interface (except the countdown interface and the main interface), if the keypad is not utilized for

1-minute, then the system will automatically return to the main interface.
When "▲" is displayed on the right side of the interface, it means the user can press <Up/Add> to achieve a

page turn.
When the right side of the interface displays "▼", it means the user can press <Down/Sub> to scroll down.

When the interface prompts "operation is currently prohibited, but operation is available XX-seconds later," it

means there is another screen operating and it needs to wait. After XX-seconds, the interface can be operated.

Icon

Meaning

Indicates temperature.

Indicates page up, parameter selection, or increasing value.

Indicates page down, parameter selection, or decreasing value.

Indicates whether the unit uses timing function.

Indicates the icon of functional keys. It is only used for Menu,

Cancellation, Return and Shift.

Indicates the icon of confirming keys. It is only used for Enter,

Confirmation, Noise Reduction, Reset and Switching Module.

Indicates the icon of ON/OFF. It is only used for starting or

shutting down the unit.

Содержание ccHPWH Series



















































Результаты поиска

Содержание ccHPWH Series

Отзывы:

Похожие инструкции для ccHPWH Series

Бренды по названию

Популярные бренды

ICE AIR ccHPWH Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание ccHPWH Series

Отзывы:

Похожие инструкции для ccHPWH Series

Бренды по названию

Популярные бренды