manualshive.com logo in svg

ICE AIR ccHPWH Series, Руководство по установке и обслуживанию, Страница: 15 / 50

Поделиться
Скачать
ICE AIR ccHPWH Series Скачать руководство пользователя страница 15

12 

 

IV. Installation 

1.  Product handling 

•

 

Confirm the unit has sufficient space for safely rigging it into place.   

•

 

Remove the protective packaging just prior to installation. 

•

 

During handling, the inclination of the unit shall not be more than 15° to prevent the unit from overturning. 

•

 

When rolling transportation is used, the same size rollers shall be placed under the base of the unit. Each 

roller must be a little longer than the outer frame of the base and suitable for the balance of the unit. 

•

 

When hoisting, the hoisting cable shall be rated for minimum of 3 times the weight of the unit. Check and 

ensure that the lifting hook is fastened to the unit, and the hoisting angle is greater than 60°. Add cloth or 

hard paper between the unit and the wire rope to prevent damage to the unit. Hoisting diagram is as follows: 

2.  Installation site selection     

•

 

The unit shall be installed in a location with ample space to allow for sufficient air flow and maintenance of 

all components.   

•

 

If the unit is in a place accessible to unauthorized personnel, isolation  safety measures should be taken, 

such as setting up protective fence, etc. 

•

 

Select locations where the sound from the unit and cool air leaving the coils will not affect the surrounding 

environment including nearby building occupants.   

•

 

The location shall facilitate the installation and maintenance of pipes and electrical connections. 

•

 

Ensure a sound foundation if mounted on grade and sufficient vibration isolation if roof mounted.   

Содержание ccHPWH Series



















































Отзывы:

Нет отзывов