IBM DCS3860 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 204

background image

The drive drawers are preinstalled in the DCS3860, but the DDMs are shipped
separately from the drive drawers. Ensure that you install the storage enclosure in
the rack cabinet before you install DDMs in the storage enclosure.

Drive
drawers

1

2

3

4

5

dcsq0004

!

Complete the following steps to install the DDMs in the drive drawers:

1.

Open the two release levers on the drawer as shown in the illustration.
Starting with the top drive drawer in the storage enclosure, pull the levers on
each side of the drawer out and cam away from the chassis to release the
drawer.

Drive drawer levers

dcsq0005

2.

With the release levers fully extended, slide the drawer out until it is fully
extended, but do not remove it from the enclosure.

3.

Starting with the first DDM, raise the DDM handle to the vertical position.

Drive
drawer

Drives

Figure 15. DCS3860 drive drawer with labeled disk drives

40

IBM System Storage DCS3860 Storage System: Installation, User's, and Maintenance Guide

«
...
56
57
58
59
60
...
»

Содержание DCS3860













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCS3860

Бренд: G-Technology Страницы: 13

Бренд: JCAT Страницы: 3

Бренд: OEM Tools Страницы: 4

SATAII/300 INTERNAL HARD DRIVE

Бренд: Maxtor Страницы: 19

TotalStorage NAS 100

Бренд: IBM Страницы: 18

Бренд: NCR Страницы: 12

Бренд: Lifetime Страницы: 40

Бренд: Lenovo Страницы: 176

Бренд: SATA Страницы: 44

Бренд: TyeDee Bin Страницы: 2

Бренд: SIRCHIE Страницы: 8

Бренд: OWIM Страницы: 13

Бренд: OWC Страницы: 8

EURO-BOXX 55/60-R

Бренд: Mullex Страницы: 2

Rasmus FR44-3857-5

Бренд: Palmako Страницы: 37

Best Barns Denver

Бренд: Reynolds Building Systems Страницы: 20

Бренд: Promise Technology Страницы: 324

Бренд: Solid Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды