IBM Aptiva 2140 Скачать руководство пользователя

Страница: 77 / 212

Table

2-1 (Page 11 of 23). POST and Diagnostics and Utilities Index

for Symptoms, Messages, Error Codes, or Beeps

Symptoms, Messages, Error
Codes, or Beeps

Action/FRU

RAM Memory Error in Block n.
Bad bits n.
Memory error.

Memory Module
System Board

RAM Test Failed.
Memory error.

Memory Module
System Board

Read error on cylinder n.
Hard disk drive format error.

Hard Disk Drive
System Board

Read Errors
Diskette drive read error.

Diskette
Diskette Drive
System Board
Diskette Drive Cable

Real-time clock is inaccurate.

Time set incorrectly by user.
RTC battery (if less than 2.8 V dc)
System Board

Receive Error.
Serial Port loopback test error.

Serial Port Cable
System Board

Refresh Failure.
Diagnostics Test detected an
error while testing the DMA
controller's RAM refresh cycle.

Memory Module
System Board

RTC Interrupt Failure.
Diagnostics Test cannot detect
the Real-Time clock interrupt.

System Board

Serial Chip Error.
COM Port error, general.

Serial Port Cable
System Board

Serial Compare Error.
COM Port error, information
transmitted is not the same as
information received.

Serial Port Cable
System Board

Serial Time-out Error.
COM Port error, time interval is
too long between transmitted
and received data.

Serial Port Cable
System Board

Serious Memory Error — Diags
Cannot Continue.
Memory Test error.

Memory Module
System Board

Check Procedures

2-21

Get user manuals:

See SafeManuals.com

Содержание Aptiva 2140





















































































































































































































Результаты поиска

Содержание Aptiva 2140

Отзывы:

Похожие инструкции для Aptiva 2140

Бренды по названию

Популярные бренды

IBM Aptiva 2140, Техническое обслуживание оборудования

Результаты поиска

Содержание Aptiva 2140

Отзывы:

Похожие инструкции для Aptiva 2140

Бренды по названию

Популярные бренды