IBM 5100 Скачать руководство пользователя

Страница: 178 / 214

164

IBM® Netfinity® 5100 User’s Reference

Troubleshooting charts

UNIX messages

This section provides descriptions of the Ethernet error messages for the SCO UNIX
LLI driver, and suggested actions to resolve each problem.

pnt0-2

PCI search specified, PCI device not found!

Explanation:

The driver cannot locate the Ethernet controller on the PCI bus.

Action:

•

Run the NETCONFIG program to search for another Ethernet controller

•

Verify that the Ethernet controller is enabled. If the Ethernet controller is enabled,
run the diagnostic programs.

pnt0-6

Cannot allocate memory for the adapter during an interrupt. Please check your
Streams parameters.

Explanation:

On a SunSoft Solaris system, this message indicates that the system is out

of Streams memory blocks.
Action:

Use the CRASH utility to increase the number of Streams memory blocks.

Modify the interrupt request (IRQ) settings in the Configuration/Setup Utility
program, or run the NETCONFIG program to match the hardware settings.

pnt0-7

Cannot allocate memory for the adapter during reset. Please check your Streams
parameters.

Explanation:

The system is out of Streams memory blocks.

Action:

Use the CRASH utility to increase the number of Streams memory blocks.

pnt0-11

Device not found!

Explanation:

The driver cannot find an Ethernet controller.

Action:

Verify that the Ethernet controller is enabled. If the Ethernet controller is

enabled, run the diagnostic programs.

pnt0-12

Device failed checksum test!

Explanation:

The driver cannot find an Ethernet controller.

Action:

Verify that the Ethernet controller is enabled. If the Ethernet controller is

enabled, run the diagnostic programs.

pnt0-13

add_intr_handler failed! Interrupts already enabled.

Explanation:

The interrupt request (IRQ) that was specified, or the IRQ that was

found, conflicts with other devices in the server.
Action:

Modify your hardware settings.

pnt0-14

Cannot locate hardware.

Explanation:

The SunSoft Solaris driver cannot find any Ethernet controller.

Action:

Verify that the Ethernet controller is enabled. If the Ethernet controller is

enabled, run the diagnostic programs.

Table 23. UNIX LLI driver messages for the Ethernet controller

Содержание 5100























































































































































































































Результаты поиска

Содержание 5100

Отзывы:

Похожие инструкции для 5100

Бренды по названию

Популярные бренды

IBM 5100, Руководство пользователя

Результаты поиска

Содержание 5100

Отзывы:

Похожие инструкции для 5100

Бренды по названию

Популярные бренды