background image

Before you begin

Read this information before beginning your installation.

Before you begin your installation, print and complete a Configuration worksheet for your storage system
to gather the information that the software setup process requires. The configuration worksheet is
provided in the

Data ONTAP Software Setup Guide

for your version of Data ONTAP, which is available on

the IBM

®

System Storage

®

N series support website:

www.ibm.com/storage/support/nseries

If you are configuring a storage system as part of a high-availability (or active/active) configuration,
some information types must be unique for each storage system mode in the configuration, and some
information types must be identical on both storage system nodes. If you have a high-availability (or
active/active) configuration, IBM recommends that you print and complete two copies of the
configuration worksheet, one for each system node.

Note:

In the Data ONTAP 7.2 and 7.3 release families, the term

active/active configuration

(or

active/active

pair

) refers to a pair of storage systems or gateways (sometimes called nodes or controller modules)

configured to serve data for each other if one of the two systems stops functioning. In the Data ONTAP
8.

x

release family, this functionality is referred to as a

high-availability (HA) configuration

or an

HA pair

.

About this document

This document provides installation and setup instructions for IBM System Storage N6040, N6060, and
N6070 filer storage systems. Additional information about these products can be found in the

N6000

Series Hardware and Service Guide

.

Additional information about the N series storage expansion units you connect to your N6000 series
system can be found in the

Hardware and Service Guides

and the

Installation and Setup Instructions

for your

storage expansion units.

Read the safety notices

Before continuing, make sure that you have reviewed the safety notices shipped with this product. Do
not plug any cables into the system, adapters, or any electrical outlets until you have reviewed the safety
information and followed the procedures in this document.

Need help?

If you encounter any difficulties while setting up your system, contact IBM service and support for
assistance. Information can also be found on the IBM System Storage N series support website:

www.ibm.com/storage/support/nseries

About the IBM N series support website

The IBM System Storage N series support website requires users to register in order to obtain access to N
series support content on the web. To understand how the N series support web content is organized and
navigated, and to access the N series support website, go to the following publicly accessible web page:

www.ibm.com/storage/support/nseries/

© Copyright IBM Corp. 2008, 2011

v

Содержание 2858-A10





























Отзывы: