IBC DC Series Скачать руководство пользователя

Страница: 62 / 82

INSTALLATION AND OPERATION INSTRUCTIONS

5-2

DC SERIES BOILERS / WATER HEATERS

DC 15-95, DC 15-96, DC 20-125, DC 33-160

ELECTRONIC COMPONENTS

This section details the method for troubleshooting the non-standard electronic

components on the boiler / water heater including the electronic water pressure

sensor – type LWCO and the temperature sensors.

5.2.1 Temperature Sensors

The resistance of the temperature sensors varies inversely with temperature. To

test, measure the temperature of the sensed environment and compare with the

value derived from the measurement of the resistance (obtained by connecting a

good quality test meter capable of measuring up to 5,000 kΩ (5,000,000Ω) at the

controller end of the sensor lead).
To obtain a resistance reading, remove power to the boiler / water heater. For

the supply water and return water temperature sensors, remove the wire leads

by disconnecting their respective Molex connectors. Place multi-meter probes

into sensor’s male Molex connector socket. Do not apply voltage to the sensor

(damage may result).

12KΩ Temperature Sensors supplied with boiler / water heater. See Table 14 for

resistance values.

SENSOR

TYPE

PURPOSE

LOCATION

NTC 12KΩ

Supply Water Temperature Upper Left of Heat

Exchanger

NTC 12KΩ

Return Water Temperature Lower Left of Heat

Exchanger

NTC 12KΩ

Domestic Hot Water

DHW Supply Pipe

NTC 10KΩ

Hot Water Tank

External Water Heater

NTC 12KΩ

Outdoor Sensor

Outdoors (North side)

NTC 12KΩ

Flue Gas Temperature

Bottom of Heat Exchanger

at Flue outlet

Water Pressure

Heating Supply Pipe

Temperature and Pressure Sensors

5.2

Water temperature sensors

TEMPERATURE RESISTANCE

F / C

Ω - ohm

F / C

Ω - ohm

F / C

Ω - ohm

5F / -15C

76,020

77F / 25C

12,000

149F / 65C

2,752

14F / -10C

58,880

86F / 30C

9,805

158F / 70C

2,337

23F / -5C

45,950

95F / 35C

8,055

167F / 75C

1,994

32F / 0C

36,130

104F / 40C

6,653

176F / 80C

1,707

41F / 5C

28,600

113F / 45C

5,522

185F / 85C

1,467

50F / 10C

22,800

122F / 50C

4,609

194F / 90C

1,266

59F / 15C

18,300

131F / 55C

3,863

203F / 95C

1,096

68F / 20C

14,770

140F / 60C

3,253

212F / 100C

952

Table 14: Temperature Sensor Resistance Values – 12KΩ sensors.

Содержание DC Series



















































































Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды

IBC DC Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды