IBC DC Series Скачать руководство пользователя

Страница: 45 / 82

2-1

BOILER SYSTEMS AND OPERATION

DC SERIES BOILERS / WATER HEATERS

DC 15-95, DC 15-96, DC 20-125, DC 33-160

2.0 BOILER / WATER HEATER

SYSTEMS AND OPERATION

GENERAL

The DC series modulating condensing boilers / water heaters are designed to heat

both your indoor space and your domestic hot water. The boiler / water heater’s

unique heat exchanger design incorporates separate copper water ways for space

heating and for domestic hot water generation.
The boiler / water heater’s control is equipped to provide outdoor reset control for

the space heating load and also can provide a set-point water temperature for the

space heating load. Installing the outdoor sensor is optional but recommended for

additional efficiency.

The boiler / water heater is equipped with a factory installed pump. The pump is

pre-wired and will operate with any call for space heating and when heating an IBC

indirect water heater. The pump will not operate with a call for domestic hot water

using the internal domestic hot water tankless coil.
The boiler / water heater pump will operate for 10 seconds every 24 hours to help

prevent pump from seizing. The pump will be energized 24 hours after the last call

for heat and every 24 hours after that until the next call for heat.
The DC series boiler / water heater can generate domestic hot water in several

ways. The DC series boiler / water heater can be used as a tankless water heater

with or without a storage tank and also with an IBC indirect water heater.
The boiler / water heater is equipped with an electronic controller, which ignites

the burner and continuously monitors the flame throughout each call for heat. The

control also displays the current operating conditions of the boiler / water heater

and any error messages should a problem occur.
The boiler / water heater’s controller also provides frost protection. When the boiler

/ water heater’s heat exchanger becomes too cold the burner switches on to keep

the heat exchanger warm. Please ensure that the condensate trap is protected from

freezing. The boiler / water heater must be installed indoors in a heated space.

2.1

BURN

HOT

DANGER

Water temperture over 125°F (52°C) can cause severe burns instantly

or death from scalds.

Children, disabled, and elderly are at highest risk of being scalded.

See instruction manual before setting temperature at boiler.

Feel water before bathing or showering.

Temperature limiting valves are available, see manual.

Содержание DC Series



















































































Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды

IBC DC Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды