IBC DC Series страница 11 Скачать руководство пользователя

Страница: 11 / 82

1-5

INSTALLATION

DC SERIES BOILERS / WATER HEATERS

DC 15-95, DC 15-96, DC 20-125, DC 33-160

•

Place in operation the appliance being inspected. Follow the lighting

instructions. Adjust thermostat so appliance will operate continuously.

•

After it has been determined that each appliance remaining connected to the

common venting system properly vents when tested as outlined above, return

doors, windows, exhaust fans, fireplace dampers and any other gas-burning

appliance to their previous conditions of use.

•

Any improper operation of the common venting system should be corrected

so the installation conforms with the National Fuel Gas Code, ANSI Z223.1 -

latest edition. In Canada, all installations must conform with the current CAN/

CGA - B149.1 Installation Code and/or local codes.

1.4.1 Applications

All DC Series boilers / water heaters must be installed as a Direct Vent venting

system. The combustion air must be piped in from the outdoors and connected

directly to the boilers / water heaters combustion air connection.

See section

1.4.7 for air intake piping requirements.

1.4.2 Exhaust Vent Material

EXHAUST VENT MATERIAL – CANADA

Only PVC, CPVC, Polypropylene (PPs) or stainless steel* vent component

systems approved under

ULC-S636 Standard for Type BH Gas Venting Systems

are to be used. Ensure compliance with exhaust temperature limitations for

the respective materials. The vent temperature is limited with the use of a flue

temperature sensor and software to ensure the maximum temperature of the

PVC venting material is not exceeded.

•

ULC-S636 PVC

•

ULC-S636 CPVC

•

ULC-S636 PPs

EXHAUST VENT MATERIAL – USA

PVC, CPVC, PPs venting materials are approved for use with this boiler /

water heater in the USA. The vent temperature is limited with the use of a flue

temperature sensor and software to ensure the maximum temperature of the

PVC venting material is not exceeded. PVC venting material shall be certified to

Sch. 40 ASTM D1785 or D2665. CPVC venting material shall be certified to Sch.

40 ASTM F441.

WARNING

Covering non-metallic vent

pipe and fittings with thermal

insulation shall be prohibited.

Содержание DC Series



















































































Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды

IBC DC Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды