IBC DC Series Скачать руководство пользователя

Страница: 46 / 82

INSTALLATION AND OPERATION INSTRUCTIONS

2-2

DC SERIES BOILERS / WATER HEATERS

DC 15-95, DC 15-96, DC 20-125, DC 33-160

2.3

CONTROL

Power Indicator

Power - ON / OFF

Space Heating

Space Heating / DHW Toggle

Domestic Hot Water

Minus

Main Display

Plus

Fahrenheit and PSI

Fahrenheit/Celsius

Celsius and Bar

Domestic Hot Water Comfort / Eco

Comfort / ECO / OFF - Indicator

Service

Comfort / ECO / OFF - Indicator

Reset Button

Service Display

Flashes to indicate a fault

Table 8: Controller Indicators and Buttons

NOTE:

The control displays codes that include upper and lower case letter and a

combination with a period after the letter. Example: C, c., c are all valid parameter

codes. When adjusting settings, double check that you are in the correct

parameter.

See DC / HC Controller Manual for details.

INSTALLER INTERFACE

2.3.1 Appliance ON/OFF

The boiler / water heater can be switched on and off with the On/Off

button.

When the boiler / water heater is “ON”, the green LED above the On/Off

button will be on. When the boiler / water heater is on and there is no call for heat

or DHW the displays are blank. When the boiler / water heater is “OFF” the main

display reads the system pressure, e.g. “14P” for 14 psi.
If the boiler / water heater is being powered up after a power outage, the boiler /

water heater will return to heating as it was when the power was removed from

the boiler / water heater.

2.2

Содержание DC Series



















































































Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды

IBC DC Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DC Series

Отзывы:

Похожие инструкции для DC Series

Бренды по названию

Популярные бренды