IBC Water AS1041MP-CL Скачать руководство пользователя страница 52

Страница: 52 / 54

AS1041MP-CL

Page

Table 3 – Troubleshooting Procedures - cont…

6. Control does not draw

brine.

a.  Low water pressure
b.  Restricted drain line.
c.  Injector or injector screen plugged.

d. Injector defective.

e. Valve general malfunction
f. Air check prematurely closed in

brine tank

a.  Increase water pressure.
b.  Remove restriction.
c.  Clean injector and screen, Refer to the

Cleaning the Injector/Injector Screen

section in this manual.

d.  Replace injector. Contact dealer.
e.  Contact dealer
f.  Replace or repair air check if needed.

Check brine line connections.

7. Intermittent or irregular

brine draw.

a. Low water pressure.
b. Defective injector.

a. Increase water pressure.
b. Replace both injector and injector cap.

Contact dealer.

8. Brine tank overflow.

a. Air leak in brine line to air check.

b. Refill program setting incorrect.

a. Check all connections in brine line for

leaks.

b. Contact dealer.

9. System using more or

less salt than estimated.

a. Inaccurate program setting of brine

refill.

b. Air check system incorrect.

c. Defective brine refill operation

control

a. Contact dealer.

b. Contact dealer.

c. Contact dealer.

10. Control backwashes at

excessively low or high
rate.

a. Incorrect backwash controller.
b. Foreign matter affecting controller

operation. !

a. Contact dealer.

b. Remove backwash controller. Clean &

replace.

11. Flowing or dripping water

at drain line after
regeneration.

a. Internal valve malfunction.

a. Contact dealer.

Содержание AS1041MP-CL























































Результаты поиска

Содержание AS1041MP-CL

Отзывы:

Похожие инструкции для AS1041MP-CL

Бренды по названию

Популярные бренды

IBC Water AS1041MP-CL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AS1041MP-CL

Отзывы:

Похожие инструкции для AS1041MP-CL

Бренды по названию

Популярные бренды