background image

SMS S8 SMART MOBILE STATION

ASSEMBLY INSTRUCTIONS

Page #

    2

Cautionary & Attention Notes

    3

Exploded SMS S8 Assembly Drawing

  4-5

SMS S8 Smart Mobile Cart Parts List

    6

Installation of Upright and Electrical Power Connect

    7

Installation of Worksurface and Lower Shelf

  8-9

Installation of Keyboard Drawer and SMS Drawer

   10

Cord Wrap Bracket and Cable Management Channel

 11-12

Installation of FPD Front Mounting UPR MTD

   13

Installation of CPU Holder

   14

ESD Information and Grounding

Cautionary Notes and Warnings:

IAC strongly recommends care must be taken during the lifting and positioning of all workstation components

as they can be heavy and awkward to lift, move and install. Only qualified installation personnel using the
proper Personal Protective Equipment should be allowed to lift any of these components into place. Failure
to use proper lifting techniques and proper Personal Protective Equipment could result in injury individuals,
the workstation and/or surrounding property. IAC Industries is not responsible for any injuries sustained or
damage to the workstation and its contents and/or damage to surrounding property caused during the proper
or improper installation of the workstation.

ATTENTION

:

IAC Industries takes great care in the packing of it's products, however damage can occur during

shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and
contact the carrier that delivered your order. Request a freight claim inspector to document the damage
and begin the freight claim process.

Tools required:

Utility knife, Safety glasses, and light duty protective gloves

NOTE: Power tools are NOT recommended unless they are equipped with a torque limiting device which can limit the

torque to 10 foot lbs maximum at aluminum attachment points, and 15 foot lbs for all other attachment points.

Unpack your order and separate like parts into separate areas.  Be careful not to damage parts as they

are being moved around and put into position. Also be sure all parts are removed from the packing
materials before these materials are thrown away.

Locate the hardware kits and keep them in a central area.  If the assembly is going to take more than

one day, all individual hardware pieces should be returned to a central location.

Check all parts and hardware kits against the itemized packing list found with the assembly instructions.

If you believe there are parts missing from your order please contact IAC Industries customer service
HOTLINE at 800-989-1422.

If your order has ESD worksurfaces or accessories please review pages 85 and 86 for cautions and

helpful suggestions before you begin assembling the workstations.

2

Содержание SMS S1 SMART MOBILE STATION





































































Отзывы: