IAC INDUSTRIES SMS S1 SMART MOBILE STATION Скачать руководство пользователя страница 61

Страница: 61 / 68

nstall 5/16-18 x .75 square head bolts (item F),

5/16 flat washer (item B), and 5/16-18 hex head
keps nuts (item G) to the top support brackets for

the worksurface and the shelf (items 2 and 3) as
shown .

Do not tighten this hardware.

Make small pencil marks on the uprights

working height of the Worksurface and the Shelf.

Install the top support brackets by installing the

square head bolts into the milled slots in the front

nut channels of the upright. Gently slide the top

support brackets to the pencil marks and tighten
the hex head keps nuts to hold them in place. Do

not tighten this hardware to more than 10 foot lbs
of torque. Doing so will cause scoring to the
aluminum of the upright.

nstall the handles (item M) to the bottom of the worksurface

(item 2) with 1/4-20 x .625 phillips head screws and 1/4 flat

washers (items D and E).

Place the Worksurface (item 2) on the top support brackets so that the cut out fits around the upright. Line up the threaded
inserts in the bottom of the worksurface with the holes in the top supports and secure with the 1/4-20 x .625 phillips head

screws and flat washers. Repeat the process with the Shelf (item 6).

SMS S8 Worksurface and Shelf Installation

Содержание SMS S1 SMART MOBILE STATION





































































Результаты поиска

Содержание SMS S1 SMART MOBILE STATION

Отзывы:

Похожие инструкции для SMS S1 SMART MOBILE STATION

Бренды по названию

Популярные бренды

IAC INDUSTRIES SMS S1 SMART MOBILE STATION, Руководство по сборке

Результаты поиска

Содержание SMS S1 SMART MOBILE STATION

Отзывы:

Похожие инструкции для SMS S1 SMART MOBILE STATION

Бренды по названию

Популярные бренды