INTRODUCTION
This manual provides guidelines and procedures for installing,
operating, and maintaining your conveyor. A complete parts list
is provided with recommended spare parts highlighted in gray.
Important safety information is also provided throughout the manual.
For safety to personnel and for proper operation of your conveyor, it
is recommended that you read and follow the instructions provided
in this manual.
• Receiving and Uncrating
1. Check the number of items received against the bill of lading.
2. Examine condition of equipment to determine if any damage
occurred during shipment.
3. Move all crates to area of installation.
4. Remove crating and check for optional equipment that may be
fastened to the conveyor. Make sure these parts (or any foreign
pieces) are removed.
• How to Order Replacement Parts
Included in this manual are parts drawings with complete replacement
parts lists. Minor fasteners, such as nuts and bolts, are not
included.
When ordering replacement parts:
1. Contact Dealer from whom conveyor was purchased or nearest
HYTROL Integration Partner.
2. Give Conveyor Model Number and Serial Number or HYTROL
Factory Order Number.
3. Give Part Number and complete description from Parts List.
4. Give type of drive. Example—8” End Drive, 8” Center Drive, etc.
5. If you are in a breakdown situation, tell us.
HYTROL Serial Number
(Located near Drive on Powered Models).
NOTE: If damage has occurred or freight is missing,
Contact your Hytrol Integration Partner.
JONESBORO, ARKANSAS
Model
XX
Hytrol Conveyor
Company, Inc.
SERIAL #
123456
Model
TABLE OF CONTENTS
INTRODUCTION
Receiving and Uncrating . . . . . . . . . . . . . . . . . . . .2
How to Order Replacement Parts . . . . . . . . . . . . .2
SAFETY INFORMATION
Installation Safety Precautions . . . . . . . . . . . . . . .3
Operation Safety Precautions . . . . . . . . . . . . . . . .3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INSTALLATION
Support Installation . . . . . . . . . . . . . . . . . . . . . . . .4
Ceiling Hanger Installation . . . . . . . . . . . . . . . . . .4
Conveyor Set-Up. . . . . . . . . . . . . . . . . . . . . . . . . .4
Electrical Equipment . . . . . . . . . . . . . . . . . . . . . . .4
Racked Sections . . . . . . . . . . . . . . . . . . . . . . . . . .5
OPERATION
Conveyor Start-Up. . . . . . . . . . . . . . . . . . . . . . . . .5
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Sequence of Operation . . . . . . . . . . . . . . . . . . . . .5
SPECIFICATIONS
E24i Motor Card Requirements. . . . . . . . . . . . . . .6
MAINTENANCE
EzLogic System . . . . . . . . . . . . . . . . . . . . . . . .6, 7
Motor Control Board . . . . . . . . . . . . . . . . . . . . .7, 8
zone Controller (EzLogic). . . . . . . . . . . . . . . . . . .7
IOP (EzLogic) . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Power Suppy (Motors). . . . . . . . . . . . . . . . . . . .8, 9
Maintenance Checklist . . . . . . . . . . . . . back cover
5 AMP Power Supply Wiring Diagram . . . . . . . .10
20 AMP Power Supply Wiring Diagram . . . . . . .11
40 AMP Power Supply Wiring Diagram . . . . . . .12
SPECIFICATIONS
E24 Motor Card Requirements . . . . . . . . . . . . . .13
The Motor Control Board. . . . . . . . . . . . . . . .14, 15
MAINTENANCE
Trouble Shooting E24 . . . . . . . . . . . . . . . . . . . . .15
Trouble Shooting E24Ez. . . . . . . . . . . . . . . . . . .15
REPLACEMENT PARTS
190-E24Ez Final Assembly & Parts List . . . . . . .16
190-E24Ez Section Assembly & Parts List. . . . .17
190-E24Ez Reflector Kit & Parts List . . . . . . . . .17
190-E24Ez Accumulation Kit & Parts List. . . . . .18
190-E24EzC Parts Drawing . . . . . . . . . . . . . . . .18
190-E24EzC Parts List . . . . . . . . . . . . . . . . . . . .19
190-E24 Parts Drawing & List. . . . . . . . . . . . . . .20
190-E24C Parts Drawing & List . . . . . . . . . . . . .21
Spanish Version . . . . . . . . . . . . . . . . . . 22
2
