manualshive.com logo in svg

Hypro 5321C-D, Руководство пользователя

Поделиться
Скачать
Hypro 5321C-D Скачать руководство пользователя страница 30

Steambrite Supply

Steambrite Supply

Created on:  : Monday 20 September, 2021 

 > 

MODEL 5324
(11 L/min.)
Pressure at Pump Outlet 3.45 MPa 3.45 MPa 6.9 MPa 5.52 MPa
Pump Inlet Conditions 127 mm/ Hg 68.9 kPa 137.8 kPa 127 mm/ Hg 68.9 kPa 137.8
kPa 127 mm/ Hg 68.9 kPa 137.8 kPa 127 mm/ Hg 68.9 kPa 137.8 kPa
Maximum Water Injected
Per Minute 266.4 ml 177.6 ml 148 ml 266.4 ml 177.6 ml 148 ml 266.4 ml 177.6 ml 148
ml 266.4 ml 177.6 ml. 148 ml
-17-
Liquid injector cylinder head MUST
be installed with the flow regulator
channel over the inlet valve of the
pump. "Inlet Side” is cast on the
cylinder head of injector for ease in
identification.
TO ADJUST THE POSITION OF THE INLET PORT
To change the position of the liquid injector inlet port, loosen the retainer nut (Ref.
5), and rotate injector body (Ref. 4) until the opening is in the desired position. It is
important that the retainer nut be fully tightened to properly compress the o-ring
seal (Ref. 3) against the valve assembly (Ref. 2)
OPERATION
Before using the injector, make sure the retainer nut is tightened securely. NOTE:
The “Inlet Port” on the body indicates the position of the dial setting
(closed position
is zero). The larger the number, the more flow is allowed. DO NOT rotate the
control knob more than three complete turns.
MAINTENANCE
If opening around needle valve stem becomes clogged, clean the valve stem and
passage way with warm soapy water. Rotate the control knob assembly
counterclockwise
(which includes the control knob and needle valve stem) until it can be
lifted out of the body. Inspect the valve stem o-ring and replace if necessary.
Install the control knob assembly by pushing down firmly on the knob and turning
clockwise until it is in the closed position. Set the injector to the desired setting.
Model No. 3396-0014, 3396-0006 Liquid Injector Heads
Ref. Quantity Part
No. Required Number Description
1 1 0257-5300C Cylinder Head for Model 3396-0014 (cast iron)
1 1 0254-5300C Cylinder Head for Model 3396-0006 (cast iron)
2 1 3400-0098 Unitized Valve Assembly
3 1 1720-0029 O-ring
4 1 3200-0027 Body
5 1 3240-0006 Retainer Nut
6 1 1720-0033 O-ring
7 1 3220-0016 Needle Valve Stem
8 1 2802-0002 Calibrated Adjustment Control Knob
DIMENSIONS INSTALLATION: IMPORTANT
PARTS LIST
1/8-27 NPT
X

Steambrite Supply - 210 662 9000 - [email protected]                       Page 30/32

Содержание 5321C-D

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды