manualshive.com logo in svg

Hypro 5321C-D, Руководство пользователя

Поделиться
Скачать
Hypro 5321C-D Скачать руководство пользователя страница 17

Steambrite Supply

Steambrite Supply

Created on:  : Monday 20 September, 2021 

 > 

5. To install the Grease Fitting into the Cam Bearing,
place the pump on the arbor press with the Safety
Cover side facing up; then press the Grease Fitting
in with the arbor press ram.
6. Grease the pump according to the Lubrication
Instructions.
7. Install the safety cover.
Symptom Probable Cause(s) Corrective Action(s)
No Flow or Low Flow Pump not primed Refer to Priming in the Operation Section.
Air leaks in suction line Check and reseal inlet fittings.
Blocked or clogged line strainer Inspect strainer and clear any debris from screen.
Undersize suction line or collapsed hose Suction line should be the same diameter as
inlet
port of Pump or larger.
Nozzle clogged Clear nozzle or replace.
Unloader or Relief Valve not functioning properly Repair or replace Relief Valve.
Low pressure Debris in Valves Remove debris. See Repair section.
Valves worn Replace Valves. See Repair section.
Unloader or Relief Valve not functioning properly Repair or replace relief valve.
Pump not primed See priming in Operation section.
Pump Leaking Seals worn Replace Seals. See Repair section.
Body cracked Replace Body. See Repair section.
-11-
Troubleshooting
Performance Data
Presssure 100 psi 300 psi 500 psi 700 psi 1000 psi
RPM GPM HP GPM HP GPM HP GPM HP GPM HP
3450 2.2 .4 2.2 .7 2.1 .9 2.1 1.2 2.0 1.5
Pressure (689.4 KPa) 2000 KPa 4000 KPa 5000 KPa (6894 KPa)
RPM I/m w I/m w I/m w I/m w I/m w
3450 8.5 298 8.3 491 7.9 756 7.7 888 7.4 1118
Presssure 100 psi 300 psi 500 psi 700 psi 1000 psi
RPM GPM HP GPM HP GPM HP GPM HP GPM HP
3100 2.3 .4 2.2 .7 2.1 .9 2.1 1.2 2.0 1.5
Pressure (689.4 KPa) 2000 KPa 4000 KPa 5000 KPa (6894 KPa)
RPM I/m w I/m w I/m w I/m w I/m w
3100 8.5 298 8.3 491 8.0 756 7.9 888 7.7 1118
100 psi 300 psi 500 psi 700 psi 1000 psi
RPM GPM HP GPM HP GPM HP GPM HP GPM HP
900 1.1 .2 1.1 .4 1.1 .5 1.1 .6 1.1 .8
1200 1.5 .3 1.5 .5 1.5 .6 1.5 .8 1.4 1.0
1450 1.8 .4 1.8 .6 1.8 .7 1.8 .9 1.8 1.2
1725 2.2 .4 2.1 .7 2.1 .8 2.1 1.1 2.1 1.4
7 BAR 20 BAR 40 BAR 50 BAR 69 BAR
RPM L/min. W L/min. W L/min. W L/min. W L/min. W
900 4.2 165 4.2 261 4.2 399 4.2 461 4.1 575
1200 5.8 224 5.6 357 5.5 536 5.5 603 5.4 739
1450 6.9 269 6.8 399 6.7 601 6.7 700 6.6 888
1725 8.2 321 8.1 459 8.0 692 8.0 815 7.9 1059
50 psi 100 psi 200 psi 300 psi 400 psi 500 psi

Steambrite Supply - 210 662 9000 - [email protected]                       Page 17/32

Содержание 5321C-D

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды