manualshive.com logo in svg

Hypro 5321C-D, Руководство пользователя

Поделиться
Скачать
Hypro 5321C-D Скачать руководство пользователя страница 24

Steambrite Supply

Steambrite Supply

Created on:  : Monday 20 September, 2021 

 > 

MODEL NUMBER.
Reference numbers are used
ONLY to identify parts in the
drawing and are NOT to be
used as order numbers.
Crankshaft Assemblies
Spec Pump No. 53702
Hollow Shaft Sub-Assembly No. 5501-5318
Consists of one No. 0550-5318 Crankshaft, one No.
2007-0029 Cam Bearing, one No. 2405-0006
Grease Fitting Assembly, one No. 1610-0011 Key,
two No. 2230-0017 Set Screws.
Hollow Shaft Assembly No. 5500-5318
Consists of one No. 5501-5318 Crankshaft Sub-
Assembly, two No. 1810-0013 Retaining Rings, two
No. 2008-0001 Main Bearings, one No. 2130-0007
Bearing Shield.
Spec Pump No. 53703
Hollow Shaft Sub-Assembly No. 5501-5320
Consists of one No. 0551-5320 Crankshaft, one No.
2007-0029 Cam Bearing, one No. 2405-0006
Grease Fitting Assembly, one No. 1610-0011 Key,
two No. 2230-0017 Set Screws.
Hollow Shaft Assembly No. 5500-5320
Consists of one No. 5501-5320 Crankshaft Sub-
Assembly, two No. 1810-0013 Retaining Rings, two
No. 2008-0001 Main Bearings, one No. 2130-0007
Bearing Shield.
Plunger Parts Kits
Plunger Stack Parts Kit No. 3430-0291
Consists of two each of the following parts:
No. 1440-0010-6 Seal Rings, No. 1440-0037
Guides, No. 1720-0064 O-rings, No. 1720-
0079 O-rings, No. 2150-0027 Seal Assemblies,
No. 2220-0039 Socket Head Cap Screws,
No. 2270-0042 Washers, and No. 2270-0051
Washers.
Plunger Parts Kit No. 3430-0292
Consists of one No. 3430-0291 Plunger Stack
Parts Kit and two No. 3500-0036 Plungers.
Ref. Qty. Part
No. Req'd. No. Description
Ref. Qty. Part
No. Req'd. No. Description
18 1 Set 3430-0197 Set of four No. 3400-0073
Unitized Valve Assemblies:
Consists of four each: O-ring (Ref. A),
Valve Seat (Ref. B), Valve Poppet
(Ref. C), Valve Spring (Ref. D), Valve
Spring Retainer (Ref. E)

Steambrite Supply - 210 662 9000 - [email protected]                       Page 24/32

Содержание 5321C-D

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды