manualshive.com logo in svg

Hypro 5321C-D, Руководство пользователя

Поделиться
Скачать
Hypro 5321C-D Скачать руководство пользователя страница 27

Steambrite Supply

Steambrite Supply

Created on:  : Monday 20 September, 2021 

 > 

4 2 2150-0047 Cup
5 2 1830-0092 Cup Holder
6 2 1720-0029 O-Ring
7 2 1440-0059 Seal Ring
8 2 1440-0060 Guide
9 1 0500-5324 Connecting Rod
10 1 0608-5300 Safety Cover
11 * 2210-0063 Cylinder Head Bolt (8 required for
Hollow Shaft Pump; 4 required for
top cylinder head ONLY on Solid
Shaft Pump)
11A 4 2210-0064 Extra Long Cylinder Head Bolt for
securing mounting base to Solid
Shaft Pump
12 2 0201-5300C Cylinder Head (Cast-Iron)
13 2 1720-0038 O-Ring
14 1 3430-0210 Ni-Resist Cylinder Sleeve Assembly:
Consists of two each of No.
1830-0033 Retainer (Ref. A), No.
1720-0079 O-ring (Ref. B), and No.
3550-0028 Sleeve (Ref. C)
Ref. Qty. Part
No. Req'd. No. Description
Piston Parts Kit
Piston Stack Parts Kit No. 3430-0191
Consists of two each of the following parts: No.
2220-0012 Cap Screw (Ref. 2), No. 2270-0011
Washer (Ref. 3), No. 2150-0047 Cup (Ref. 4), No.
1720-0029 O-ring (Ref. 6), No. 1440-0059 Seal Ring
(Ref. 7) and No. 1440-0060 Guide (Ref. 8).
Crankshaft Assembly Kits
Model 5324C
Solid Shaft Sub-Assembly No. 5001-5321
Consists of one each of the following parts: No.
0500-5321 Crankshaft, No. 1600-0014 Crankpin
Retainer, No. 2007-0029 Cam Bearing, No. 2405-
0006 Grease Fitting Assembly, No. 1610-0007 Key.
Model 5324C-H
Hollow Shaft Sub-Assembly No. 5501-5321
Consists of one No. 0550-5321 Crankshaft, one No.
1600-0014 Crankpin Retainer, one No. 2007-0029
Cam Bearing, one No. 2405-0006 Grease Fitting
Assembly, one No. 1610-0011 Key, two No. 2230-
0017 Set Screws.
Hollow Shaft Assembly No. 5500-5321
Consists of one No. 5501-5321 Crankshaft Sub-
Assembly, two No. 1810-0013 Retaining Rings, two
No. 2008-0001 Main Bearings, one No. 2130-0007
Bearing Shield.
11

Steambrite Supply - 210 662 9000 - [email protected]                       Page 27/32

Содержание 5321C-D

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды